Installation Guide Outdoor CPE CPE210 / CPE220 / CPE510 / CPE520 Contents Overv

Installation Guide Outdoor CPE CPE210 / CPE220 / CPE510 / CPE520 Contents Overview  01 Hardware Connection  04 Site Consideration  04 Connection and Installation  06 Lightning & ESD Protection  08 Software Configuration  10 Logging in to the PharOS  10 Typical Application Configuration  12 Antenna Alignment  14 Specifications  15 FAQ  16 01 Overview TP-Link's Pharos series outdoor CPEs are dedicated to outdoor wireless network solutions. This guide is applicable to products including CPE210, CPE220, CPE510 and CPE520. • Package Contents Installation Guide Outdoor CPE CPE210 / CPE220 / CPE510 / CPE520 Pharos CPE Passive PoE Adapter Pole Mounting Straps Mounting Bracket Plastic Wall Anchors (Qty.2) Self-tapping Screws (Qty.2) Installation Guide Power Cord • LED Explanation The following picture takes CPE520 as an example. POWER LAN0 LAN1 AP/AP Router mode: All four LEDs remain solid. Client/Bridge/Repeater/AP Client Router mode: That the more LEDs lit will indicate better wireless signal strength. Flashing: A device is connected to this port, and is active. On: The CPE is powered on. On: A device is connected to this port, but there is no activity. 02 • Panel Layout Pharos CPE220/CPE520: Shielded Ethernet Port LAN0 (Passive PoE in) RESET Shielded Ethernet Port LAN1 Grounding Terminal Pharos CPE210/CPE510: Shielded Ethernet Port LAN (Passive PoE in) Grounding Terminal RESET 03 Passive PoE Adapter: Remote Reset Press and hold for 8 seconds to reset the CPE to its factory defaults. Power LED The Power LED is on when the passive PoE adapter is working normally. 04 Hardware Connection 1. Site Consideration • Mounting Height Ensure a clear line of sight between the wireless devices for an optimum performance. An elevated location is recommended as obstacles like trees, buildings and large steel structures will weaken the wireless signal. See 'Q2' in 'FAQ' for details about how to calculate the minimum mounting height of the devices. Line of Sight Side View 05 • Orientation Install the CPE devices with the front facing the intended signal receiving devices. You can orient the devices with the assistance of Google Maps, GPS and some landmarks according to the horizontal beamwidth listed below. Models CPE210 CPE220 CPE510 CPE520 Horizontal Beamwidth 65° 60° 45° 45° A shenzhen B Line of Sight Horizontal Beamwidth 06 2. Connection and Installation Connect and mount the CPE and power adapter as shown below. The following introduction takes CPE520 as an example. • Connecting CPE and Power Adapter Connect the CPE and power adapter as shown in the figure below. Ethernet cable length up to 60m You should prepare an adequate Ethernet cable to connect the CPE and the passive PoE adapter. Shielded CAT5e (or above) cable with ground wire is recommended (refer to the next section). Connect to a computer, router or switch. (Depending on your intended usage and/or network topology.) Slide to replace the cover of the CPE when all connections are finished. LAN0 PoE LAN 07 • Mounting CPE At the selected site, approximately align the CPE to the direction that you have oriented. • Mounting Power Adapter (Optional) Follow the steps below to mount the power adapter: To ensure the passive PoE adapter is attached most securely, it is recommended to install the adapter with the Ethernet port facing upward. 1. Drill two holes on the wall and insert the plastic wall anchors into the the holes. Secure the mounting bracket to the wall. Make sure the shoulders at the corners of the mounting bracket are on the outside and pointing upward. 2. Attach the passive PoE adapter to the mounting bracket by sliding the adapter in the direction of the arrows until it locks into place. 08 3. Lightning & ESD Protection Proper grounding is extremely important for outdoor devices. By using shielded CAT5e (or above) cable with ground wire for the connection and the provided PoE adapter (method 1 ), you can effectively eliminate ESD attacks. If you use the general CAT5e cable for the connection, then it is necessary to connect the grounding terminal of the CPE to earth ground through grounding cable (method 2 ). The following introduction takes CPE520 as an example. CPE Grounding Terminal Earth Ground Two Methods: 2 2 1 1 1 1 PoE Adapter with Earth Ground Grounding Cable Shielded CAT5e (or above) Cable with Ground Wire Grounding Terminal and Cable Shielded CAT5e (or above) Cable with Ground Wire Grounded 3-wire Power Outlet 09 Twisted Pair Ground Wire Shielded RJ45 Connector Secondary Cable Shield Cable Shield Sheath Shielded CAT5e (or above) Cable with Ground Wire 10 Software Configuration This chapter introduces the login to the PharOS Web Interface and the software configurations. 1. Logging in to the PharOS 1. Before accessing the PharOS Web Interface, you need to assign a static IP address 192.168.0.X (X ranges between 2 and 253, e.g. 192.168.0.10) to your computer. 2. Open a web browser, type http://192.168.0.254 into the address field and press Enter (Windows) or return (Mac). It is recommended to use the latest version of Google Chrome, Firefox or Safari. 11 3. Enter admin for both User Name and Password. Read and agree the terms of use, then click Login. 4. Change the default User Name and Password to protect your CPE. Let’s start configuring the CPE. For subsequent logins, use the new username and password. For more configurations, please visit http://www.tp-link.com/support to download the User Guide of PharOS products in the download center. 12 2. Typical Application Configuration The typical topology is as follows. A wireless bridge is built between two locations that are far from each other. Follow the instructions below to configure the Access Point and the Client. Access Point Client Computer IP camera LAN: 192.168.0.254 LAN: 192.168.0.2 Configure the Access Point (AP) 1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Access Point and click Next. 3. LAN Settings: Click Next. 4. Wireless AP Settings: a. Create a new SSID (Network name) for your wireless network. b. Select WPA-PSK/WPA2-PSK for the Security method and create a PSK Password to protect your AP. c. Enter the distance between the Access Point and the Client into the Distance Setting field. d. Select the MAXtream checkbox (Refer to Q3 in FAQ for details about MAXtream), and click Next. 5. Finish: Verify your settings and click Finish to complete the configuration. Configure the Client 1. Log in to PharOS and go to the Quick Setup page. 2. Operation Mode: Select Client and click Next. 13 3. LAN Settings: Change the IP Address to 192.168.0.X (X ranges between 2 and 253), the same subnet with the access point, and click Next. 4. Wireless Client Settings: a. Click Survey and select the SSID of the Access Point in the AP list, then click Connect. b. Select WPA-PSK/WPA2-PSK from the Security option, enter the same PSK password and distance value of the Access Point, then click Next. 5. Finish: Verify your settings and click Finish to complete the configuration. For more configurations, please visit http://www.tp-link.com/support to download the User Guide of PharOS products in the download center. 14 Antenna Alignment In order to get the best performance, you can precisely align the direction of the CPE with the assistance of Wireless Signal Quality on STATUS page of the PharOS Web Interface. Adjust the direction of the CPE until the device reaches the highest SNR. WISP WISP 15 Specifications HARDWARE FEATURES Dimensions CPE520/CPE220: 275.83*79*60.3mm CPE510/CPE210: 224.34*79*60.3mm Interface CPE520/CPE220 CPE510/CPE210 LAN0: 10/100Mbps Ethernet Port (PoE IN) LAN1: 10/100Mbps Ethernet Port LAN: 10/100Mbps Ethernet Port (PoE IN) GND: Grounding Terminal for Lightning Protection RESET: Button to restore the device to Factory Default Power Supply 24V Passive PoE Adapter Included ESD Protection1 15kV Lightning Protection1 Up to 6kV Operating Temperature -40℃to 70℃ (-40 ℉to 158 ℉) Operating Humidity 10% to 90% Certification CE, FCC, RoHS, IPX5 WIRELESS FEATURES Models CPE210 CPE220 CPE510 CPE520 Antenna Gain 9dBi 12dBi 13dBi 16dBi Horizontal Beamwidth/Elevation Beamwidth2 65°/ 35° 60°/ 30° 45°/ 30° 45°/ 30° 802.11 Standards 11b/g/n 11b/g/n 11a/n 11a/n Note: 1. Estimation is based on copper grounding cable and shielded CAT5e cable with ground wire. 2. Beamwidth values may vary throughout operating frequency. 16 FAQ Q1. How to restore the CPE to its factory default settings? With the CPE powered on, press and hold the RESET button on the CPE or the Remote Reset button on the passive PoE adapter for about 8 seconds until the Wireless Signal Strength LEDs flash. Method 1: The following picture takes CPE520 as an example. RESET Button Press & hold for about 8 seconds Method 2: Remote Reset Button Press & hold for about 8 seconds 17 Q2. How to calculate the minimum mounting height of the devices? In order to maximize the received signal strength of the devices, installers need to minimize the effect of the out-of-phase signals, which is caused by obstacles in the path between the transmitter and the receiver. Fresnel Zone is a usual method to calculate this path, as shown in the formula and the uploads/s3/ installation-guide 7 .pdf

Tags
Administrationdevice pharos interference cable click
Documents similaires
  • 52
  • 0
  • 0
Afficher les détails des licences
Licence et utilisation
Gratuit pour un usage personnel Attribution requise
Partager