Remerciez-le!

Remerciez @Admin pour avoir partagé cet document gratuitement, de la manière la plus simple, en partageant sur les réseaux sociaux.

Build Guide - Ender 5 ExoSlide XY Motion Kit 7/30/19 www.exoslide.com 1. Corner

Build Guide - Ender 5 ExoSlide XY Motion Kit 7/30/19 www.exoslide.com 1. Corner Bracing (to keep the same travel): Parts Needed: Corner brace, 2x M5x8 bolt, 4x M5 T nut, 4x 2x Notes: -Remove the front aluminum corner braces and install the supplied shorter braces. Do this before loosening the front Y belt brackets to keep the 2020 alignment. 2. V-wheel Bracket Removal: -Loosen front Y belt brackets. -Remove all V-wheel brackets (X bracket and both Y brackets). -Leave Y belts draped over the frame. -Put aside two M5x20 bolts from the Y brackets, and the M8 bolt, nuts, and bearings from the Y belt tensioner on your Ender 5 printer. 3. Tensioner Bracket Assembly: Parts Needed: Tensioner bracket, 1x M5x8 bolts, 2x M5 T nut, 2x Re-use: M8 bolt, nuts, bearings 4. Idler Bracket Assembly: Parts Needed: Idler brackets, 1x M5x8 bolt, 1x M5 T nut, 1x M8x25 bolt, 1x M8 washer, 1x M8 thin nut, 1x M8 locknut, 1x F688 bearing, 2x Re-use: M5x20 bolt 5. Motor Bracket Assembly: Parts Needed: Motor brackets, 1x M5x8 bolt, 1x M5 T nut, 1x M3x8 bolt, 3x M8x25 bolt, 1x M8 washer, 1x M8 thin nut, 1x M8 locknut, 1x F688 bearing, 2x Re-use: Motor, M5x20 bolt 6. X Carriage Assembly: Parts Needed: ExoSlide 20PC, 4x Carriage bracket, 1x M4x42 bolt, 8x M4x18 bolt, 2x M3x20 bolt, 2x M3x5 spacer, 2x Notes: -Tighten the eight M4x84 Nylock bolts down firmly that secure the four ExoSlides together. 7. Endstop Assembly: Parts Needed: Endstop bracket, 1x M4x18 bolt, 1x M4 T nut, 1x Re-use: M3x6 bolts, endstop 8. Gantry Assembly: Parts Needed: Tensioner bracket assembly, 1x Idler bracket assembly, 1x Motor bracket assembly, 1x X carriage assembly, 1x Endstop assembly, 1x Bracket 20mm, 2x Belt, 1x Re-use: 2020 cross rail Notes: -Install the idler bracket assembly and the motor bracket assembly with the long M5x20 bolts screwed into the tapped holes at the ends of the extrusion. -Install the black plastic brackets with the tabs pointing to the ends of the 2020 rail. Leave the bolts loose, and the brackets roughly 10mm away from the aluminum brackets. -Nest the endstop switch into the top of the black plastic bracket. 9. Y Carriage Assembly: Parts Needed: ExoSlide 20PC, 2x M4x35 bolt, 4x Endstop Y, 1x Notes: -Tighten the four M4x35 bolts down firmly that secure the ExoSlides together. 10. Y ExoSlide: Parts Needed: ExoSlide 20PC, 1x 11. Motion Assembly: Parts Needed: Gantry assembly, 1x Y carriage assembly, 1x Y ExoSlide, 1x M4x18 bolt, 4x Notes: -Place the gantry assembly over the rails, then install the Y belts first. -Now slide the black brackets to line-up with the ExoSlides (two farthest holes). -Then tighten the Y (and X if not done yet) belts. -Go make stuff! uploads/s1/ ender5-build-guide.pdf